Repair cost
Maytag gas dryer igniter and valve repair cost
What gas dryer igniter and valve repair costs on a Maytag in South Florida, from $175, and what moves that figure up or down. No final price is published anywhere on this site: the exact cost is confirmed on site after the diagnostic and agreed in writing before anything is opened.
- From $89 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
The short version
Where this figure comes from
A starting point for built-in appliances in South Florida, published so the number is not a mystery until somebody is standing in your kitchen.
Starts at
from $175
After a diagnostic from $89, which comes off the bill when you go ahead with the work.
or call (305) 853-8839
It is not
A quote for your unit
Exact cost
Confirmed after the on-site diagnostic
Warranty
On the labor we performed
What moves it
Why two of the same job cost different amounts
These apply at the same time and in both directions. Which of them is true of your kitchen is what the on-site diagnostic settles.
-
Igniter, sensor or coils
Three parts at three prices. The igniter is the commonest and the cheapest; the coils are the dearest and are proved rather than assumed.
-
Whether it lights at all
Lighting and dying is flame sensing; never lighting is ignition. That distinction moves the figure and it is free to observe.
-
Testing afterwards
Gas work is leak-tested and run through a full cycle before the machine is handed back, and that time sits inside the figure rather than being skipped to make a number look better.
-
Airflow
A gas machine cuts out on the same overheat protection as an electric one, so the run is checked here too.
The work itself
What we actually do
The job behind the figure: what it involves, when a symptom points at it, and what we check first.
-
from $175 Gas dryer igniter and valve repair
On a gas machine the igniter is the usual answer and it fails in a way that looks exactly like no heat at all — it weakens for months before it stops, so the complaint that arrives is a dryer taking two cycles rather than a dryer that is cold. After that it is the flame sensor and the valve coils, and the order matters because two of the three are inexpensive and one is not.
- A weakening igniter arrives as slow drying, not as no heat
- Flame sensor and valve coils measured, not swapped in hope
- The duct is checked here too — a gas machine overheats for the same reasons
In more detail
About Maytag gas dryer igniter and valve repair cost
Why this figure is a from
Level with the element row, and for the same reason: the parts are modest and the figure carries the diagnosis and the airflow. Where a gas machine differs is that the start sequence is visible, so watching one cycle usually names the part before a meter comes out — which makes this one of the faster diagnoses on the site.
What puts your job at the bottom of the band
One appliance, reachable, and a cause that turns out to be a setting, a filter, a duct or something cleared rather than replaced. The parts channel behind this make is as wide as any on this fleet — a pump, a lock, a valve, an element or a belt is stocked locally and several of them fit dozens of model numbers — so most of this list is a one-visit job and the visit that finds the problem is very often the visit that fixes it.
What puts it at the top
Access, age and measurement. A wall oven in a tall housing, a stacked pair in a closet, or a machine that has not been pulled out since it was installed is time before the work starts. Age is the variable this make has more of than its sisters: it is bought to be kept, so seized fasteners and a console that has been off before are ordinary here. And on the cold half there is the diagnosis itself — this maker publishes twenty-six numbered conditions across five hundred and nine refrigeration pages, and none at all for any freezer or for a top-freezer cabinet, so a cold-side visit is measured rather than read. Its ovens, ranges and washers publish hundreds, and those narrow faster and cheaper.
When we say do not repair it
There is a point where a repair stops making sense, and on this make it arrives later than on most — that is the whole argument for the badge. A fifteen-year-old washer with a sound drum is usually worth a pump, a lock or a suspension. The same machine with a failed bearing and a tired cabinet is usually not. You are told which of those you have, with the numbers, before anything is ordered, and the diagnostic you paid for is what bought that answer.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Maytag gas dryer igniter and valve repair cost
Why is it a from and not a price?
Because the same job is not the same work on two machines. The part, the access and what the appliance has done to itself all move it, and naming a figure before measuring is guessing with extra confidence. The exact cost is confirmed on site and agreed in writing before anything is opened, ordered or charged.
Is it worth repairing, or should I replace the machine?
On this badge that question has a later answer than on most, which is what people buy it for. The equipment we open is routinely older than the kitchen around it and still worth keeping. Where it is not, you are told plainly and with the arithmetic, on the visit rather than afterwards.
Is the diagnostic charged on top?
It pays for the diagnosis, which is real work — and on the cold half of this make it is the larger part of the job, because there is nothing published to read. If you go ahead with the repair it comes off the bill, so you pay it once either way.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name