Repair cost
Maytag dryer moisture sensor service cost
What dryer moisture sensor service costs on a Maytag in South Florida, from $109, and what moves that figure up or down. No final price is published anywhere on this site: the exact cost is confirmed on site after the diagnostic and agreed in writing before anything is opened.
- From $89 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
The short version
Where this figure comes from
A starting point for built-in appliances in South Florida, published so the number is not a mystery until somebody is standing in your kitchen.
Starts at
from $109
After a diagnostic from $89, which comes off the bill when you go ahead with the work.
or call (305) 853-8839
It is not
A quote for your unit
Exact cost
Confirmed after the on-site diagnostic
Warranty
On the labor we performed
What moves it
Why two of the same job cost different amounts
These apply at the same time and in both directions. Which of them is true of your kitchen is what the on-site diagnostic settles.
-
Cleaning or replacing
Cleaning is the answer in most cases. A strip that has been damaged or a wiring break behind it is the part, and it is a modest one.
-
Whether a timed cycle works
If it dries on timed and not on auto, this is the answer and nothing in the heat circuit needs touching. That comparison is free.
-
Whether it is really the sensor
A restricted duct produces the same complaint from a different direction, and both are checked before either is charged for.
-
How much residue there is
Years of softener leaves a film that takes more than a wipe to remove, and on a machine used daily by a family that is honest additional time rather than a two-minute job.
The work itself
What we actually do
The job behind the figure: what it involves, when a symptom points at it, and what we check first.
-
from $109 Dryer moisture sensor service
Two metal strips inside the drum that decide when the load is dry, and fabric softener leaves a film on them. A coated sensor reads a wet load as dry and ends the cycle early, which arrives as a complaint about heat and is nothing of the kind — the machine is warm, the cycle is short, and the clothes come out damp. It is a two-minute job and it is worth ruling out before anything else is booked.
- Softener residue on the sensor ends cycles early: it looks like a heat problem
- Cleaned rather than replaced in most cases
- Auto cycles behave differently from timed ones, and that difference is the clue
In more detail
About Maytag dryer moisture sensor service cost
Why this figure is a from
Among the lowest rows because the repair is usually cleaning rather than replacing. Two metal strips inside the drum, a film of softener residue, and a cycle that ends early — the test costs nothing and the fix takes minutes. It is priced as a visit because the diagnosis that gets you here is worth having.
What puts your job at the bottom of the band
One appliance, reachable, and a cause that turns out to be a setting, a filter, a duct or something cleared rather than replaced. The parts channel behind this make is as wide as any on this fleet — a pump, a lock, a valve, an element or a belt is stocked locally and several of them fit dozens of model numbers — so most of this list is a one-visit job and the visit that finds the problem is very often the visit that fixes it.
What puts it at the top
Access, age and measurement. A wall oven in a tall housing, a stacked pair in a closet, or a machine that has not been pulled out since it was installed is time before the work starts. Age is the variable this make has more of than its sisters: it is bought to be kept, so seized fasteners and a console that has been off before are ordinary here. And on the cold half there is the diagnosis itself — this maker publishes twenty-six numbered conditions across five hundred and nine refrigeration pages, and none at all for any freezer or for a top-freezer cabinet, so a cold-side visit is measured rather than read. Its ovens, ranges and washers publish hundreds, and those narrow faster and cheaper.
When we say do not repair it
There is a point where a repair stops making sense, and on this make it arrives later than on most — that is the whole argument for the badge. A fifteen-year-old washer with a sound drum is usually worth a pump, a lock or a suspension. The same machine with a failed bearing and a tired cabinet is usually not. You are told which of those you have, with the numbers, before anything is ordered, and the diagnostic you paid for is what bought that answer.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Maytag dryer moisture sensor service cost
Why is it a from and not a price?
Because the same job is not the same work on two machines. The part, the access and what the appliance has done to itself all move it, and naming a figure before measuring is guessing with extra confidence. The exact cost is confirmed on site and agreed in writing before anything is opened, ordered or charged.
Is it worth repairing, or should I replace the machine?
On this badge that question has a later answer than on most, which is what people buy it for. The equipment we open is routinely older than the kitchen around it and still worth keeping. Where it is not, you are told plainly and with the arithmetic, on the visit rather than afterwards.
Is the diagnostic charged on top?
It pays for the diagnosis, which is real work — and on the cold half of this make it is the larger part of the job, because there is nothing published to read. If you go ahead with the repair it comes off the bill, so you pay it once either way.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name