MaytagRepair Miami
(305) 853-8839 Book a visit

Broward · South Florida

Maytag repair in Pompano Beach

Coastal buildings and inland streets in the same city. Where the unit sits relative to the water is the first thing that tells us what to expect from the condenser.

We cover Pompano Beach and the rest of Broward: an on-site diagnostic first, the price agreed in writing before anything is opened, and the exact figure confirmed once we have seen the unit.

Book a diagnostic (305) 853-8839

By unit

Start with whichever matches yours. How an appliance is installed shapes the visit as much as the repair does, which is why we ask about it when you book.

  • A front-load dryer beside a small laundry-room window at dusk, blue light across its flat front
    Electric and gas · vented · commercial-grade residential

    Maytag dryer repair in Pompano Beach

    189 pages and 56 of them numbered, plus a commercial branch of 73 pages with 39 more. Every dryer under this badge is a vented machine — there is no heat-pump model and no compact one, which is a real difference from the sister brands in the same corporation and it decides the whole diagnosis. A vented dryer lives or dies by the duct behind it, and in South Florida that duct is more often long and horizontal than short and vertical, and it carries air that arrived with plenty of moisture of its own. So a dryer here gets slower every season until somebody finally counts the cycles, and the machine at that point is usually fine.

    • Vented electric and gas dryers, and the commercial-grade residential machines
    • 56 code pages, and 39 more on the commercial dryer
    • No heat-pump and no compact model — the duct is the diagnosis
    Dryer repair
  • The ice storage bin lifted out of a refrigerator with the empty ice compartment behind it
    The ice maker inside the refrigerator — in the door or in the freezer

    Maytag ice maker repair in Pompano Beach

    Maytag builds no ice machine of its own, and this page is honest about that instead of describing a sister brand's product. Every one of the 120 ice pages in the maker's base is filed under a refrigerator, beneath headings it calls Ice and Water Concerns and Ice Production, and not one of them carries a number. So there is nothing here to read off a panel. What there is, in a city that gets through ice the way this one does, is a module that spends August at the edge of what it was specified to do — and a short list of reasons it falls off that edge, most of which are about the supply rather than the module.

    • The refrigerator's own ice maker, in the door or in the freezer compartment
    • No ice machine under this badge, and no published codes for ice at all
    • The usual answer is upstream of the module: filter, line, valve, pressure
    Ice maker repair
  • A dishwasher door open to horizontal in a dark kitchen with the lower rack halfway out, a plain stainless front in a dark cabinet run
    Front control and top control · stainless and plastic tubs

    Maytag dishwasher repair in Pompano Beach

    296 pages with 42 numbered conditions, and a code branch of its own — 38 of those 42 sit under a single heading the make calls Error Code or Flashing Lights. That last phrase is the useful part: on a machine with no digital display the diagnosis is a pattern of blinking lights, and the pattern is the whole message. It disappears the moment the power is cut, which is why we ask what the lights were doing before anybody reached for the breaker.

    • Front-control and top-control machines, stainless and plastic tubs
    • 42 code pages, 38 of them under one Error Code or Flashing Lights heading
    • On a machine with no display, the blinking pattern IS the code
    Dishwasher repair
  • A single built-in wall oven set at chest height into a tall column of near-black cabinetry, door closed, plain handle, the glass dark and the fascia unreadable.
    Single and double wall ovens · built into the cabinetry

    Maytag wall oven repair in Pompano Beach

    175 code pages out of 293 — proportionally the most documented appliance in this catalog, and the one where the display is most likely to have already done the diagnosis. A wall oven is also the appliance where getting to the part costs more than the part: it is built into a tall housing, it is heavy, and on a double oven it is heavier still. So the visit is planned differently. We want the code and the model before the van is loaded, because a wall oven pulled out twice is a wall oven pulled out once too often.

    • Single and double wall ovens, built into a run of cabinetry
    • 175 code pages of 293 — the most numbered appliance this make publishes
    • Access is the expensive half: the code decides what comes on the first visit
    Wall oven repair
  • A white top-load washing machine standing in a narrow laundry closet at dusk with its lid raised, an empty stainless basket below and a tall finned center agitator post rising from the middle of it.
    Top load · front load · commercial-grade residential

    Maytag washer repair in Pompano Beach

    This is the deepest branch of Maytag's own support base and the oldest thing the badge does — the company has been building washing machines since 1907. 479 pages, and 158 of them are code pages: 86 on the top-load machine, 62 on the front-load. That is more numbered diagnosis than the whole refrigeration half of the catalog gets, and it changes how a washer call starts. On most makes we ask what the machine is doing; here we ask what it is showing, because it will usually be showing something. The top-loader is the one Maytag is bought for and the one that outlives its kitchen — which is also why so many of the machines we open here are older than the room around them.

    • Top-load, front-load and commercial-grade residential machines
    • 86 code pages on top load, 62 on front load — the make's most documented appliance
    • Older machines are normal here: the badge is bought to be kept
    Washer repair
  • A tall single-door upright freezer standing against a utility-room wall with its door open on empty shelves
    Upright · chest · convertible chest

    Maytag freezer repair in Pompano Beach

    184 pages in the maker's base and **not one numbered code** — upright, chest and convertible chest alike. A freezer under this badge is a deliberately simple machine and it is diagnosed the way simple machines are: by temperature, by airflow, by the seal, and by where it stands. That last one matters more here than anywhere. Most of the freezers we open in South Florida are in a garage or a utility room that reaches a hundred degrees by afternoon, and an ordinary cabinet asked to hold zero in that ambient is working far outside what its specification assumed. Garage-ready is a specification with a number behind it, not a slogan.

    • Upright, chest and convertible chest freezers
    • No published codes at all — 184 pages of plain guidance
    • Where it stands is half the diagnosis: a hot garage is a different machine
    Freezer repair

By job

Starting figures for this equipment in South Florida. What moves them is the model, the access and the part — the exact cost is confirmed after the on-site diagnostic.

  • The side cover of an over-the-range microwave off on a bench showing the magnetron block, the capacitor and the transformer, an insulated screwdriver laid by. The capacitor is the reason this page tells owners to stop, and it is in the frame.
    from $165

    Microwave repair

    Sixty-seven of this maker's seventy-six microwave code pages belong to the over-the-range machine, which is the one worth repairing. It is fitted, wired, often ducted, and it carries the ventilation for the range beneath it — so replacing one is a carpentry job on top of an appliance one and the repair usually wins. On a countertop machine the arithmetic runs the other way and we say so on the phone rather than after a visit.

    • Over-the-range machines: fitted, ducted, and the hood as well
    • On a countertop machine we will usually tell you not to bother
    • The high-voltage side is the last thing opened, not the first
    What this involves
  • Flexible tubing fed into the drain trough at the bottom of an evaporator compartment with a tray under the machine. The blocked defrost drain is the cause of most water under the crispers, which is what this page is called out to.
    from $135

    Refrigerator leak repair

    Water inside the cabinet, under it, or on the floor beside it, and the three have different answers. Inside is nearly always the defrost drain backing up and refreezing; underneath is the drain pan or the tube that feeds it; beside it is the supply line, which is plumbing wearing an appliance complaint. In a kitchen with wood floors or a cabinet run either side, this is a today job rather than a weekend one.

    • Inside, underneath and beside are three different repairs
    • The drain is cleared and the reason it blocked is dealt with
    • The cabinetry is checked before we leave, not after it swells
    What this involves
  • A washer pulled out with its upper rear panel off, the inlet valve drawn out on its bracket with both braided supply hoses still attached. Two hoses is the detail: this page is about why a machine fills cold only.
    from $139

    Washer water inlet valve repair

    A machine that fills slowly, fills on one temperature only, or will not fill at all. Most of it is upstream — screens, hoses and shut-offs that have not been turned since the machine was installed — and the valve itself is a modest part. In an older laundry closet the shut-offs are frequently the oldest thing in the room and worth replacing while the machine is out.

    • Screens and shut-offs first: they are older than the machine in most closets
    • Filling on one temperature only points at one half of the valve
    • Measured under pressure, because a valve can pass at rest and stall under load
    What this involves
  • A bake element unbolted from the floor of an oven cavity and drawn forward a hand's width on its two leads, held in a gloved hand, the cavity dark behind and one work light raking in from the open door.
    from $155

    Oven not heating repair

    Cold, or heating to the wrong number, and the two are different jobs. This is the most documented appliance the maker builds — a hundred and seventy-five numbered pages out of two hundred and ninety-three on wall ovens — so the display usually names the subsystem before anybody arrives. On a wall oven the price carries the access as much as the part: a tall housing, a heavy cabinet and a run of joinery either side.

    • The display usually names the subsystem: photograph it before switching off
    • Consistently wrong and swinging wrong are different diagnoses
    • On a wall oven the access is most of the cost, so the code decides the first visit
    What this involves
  • A green control board lifted out of an appliance and laid on a dark antistatic mat under one low lamp, two ribbon connectors still trailing back into the opening, relays and a large capacitor visible, nothing on the board readable.
    from $265

    Appliance control board repair

    Everybody reaches for this part first, and the manufacturer's own documentation asks that it be proved innocent before it comes out. One control architecture runs across this whole corporation, which is why a letter-and-number on a range looks so much like one on a washer — and why a board diagnosed by resemblance rather than by measurement gets replaced perfectly well and changes nothing. Boards seldom die of nothing, and whatever killed this one is still in the appliance when the new one goes in.

    • Proved before it is condemned: supply, harness and the connections into it
    • A browned connector or a pin backed out of its housing is cheap; a board is not
    • Programmed to your model afterwards, or the appliance behaves oddly in ways nobody links back
    What this involves
  • A finger tracing a wet line along the bottom edge of an open dishwasher door where the seal meets the tub, a dark puddle on the tile. The door gasket is the first thing checked and the bottom edge is where it shows.
    from $145

    Dishwasher leak repair

    Water on the floor in front of the machine, or under a cabinet run where nobody sees it for months. Finding it costs more than fixing it: a door gasket, a sump seal, a hose that weeps only under pressure at one point in the cycle. In a fitted kitchen the expensive half of this repair is the joinery, so it is dealt with as a today job rather than a weekend one.

    • Found by running the machine and watching, not by guessing at the part
    • A leak that appears at one point in the cycle points at one part
    • The cabinet base is inspected before we leave
    What this involves

Nearby

Where else we work near Pompano Beach

Every place below has its own page, with what the equipment and the access are like there.

Elsewhere in Broward

See the whole service area

In more detail

Maytag repair in Pompano Beach, in more detail

What Maytag equipment is like in Pompano Beach

Coastal buildings and inland streets in the same city. Where the unit sits relative to the water is the first thing that tells us what to expect from the condenser.

Pompano Beach sits in Broward County, and the equipment here follows the housing: older kitchens with appliances fitted into openings that were cut for something else, and newer ones where they were specified with the cabinetry. Both are Maytag work — cooktops, dishwashers, dryers — and both are diagnosed on site before anything is priced.

Salt, heat and storms — what they do to a kitchen full of appliances

Close to the water everything ages from the outside in. Salt corrodes the condenser coils and fan motors on the cold side and reaches burner caps, grates and igniters on the hot side, and both fail in the same way: a part that still works, slowly, until the day it does not. In Pompano Beach that turns a cleaning interval into a seasonal job rather than an annual one, on both halves of the kitchen.

What that means for the appliances in Pompano Beach

  • Range hoods — Almost nothing in a tower vents outside, so the hood recirculates and lives entirely on a charcoal filter — a consumable most owners have never been told about, and the reason a healthy-sounding hood can move nothing at all.
  • Dishwashers — Tower kitchens are narrow, so an 18-inch dishwasher in a galley is a normal sight here rather than an unusual one — and a part for it comes up in the service elevator, which is booked before the visit rather than on the day.
  • Refrigerators — A refrigerator in a tower has less air around it and a warmer cabinet behind it than the same unit in a house, so the condenser matters more here and the cleaning interval is shorter than the manual assumes.

How a visit in Pompano Beach is arranged

We ask for the model number from the plate inside the door and a line about what the appliance is doing. That decides which parts ride in the van, and it is the difference between one appointment and two.

  • In a building: the service elevator window, the loading bay and the hours contractors are allowed to work
  • Behind a gate: how visitors are cleared, arranged before the appointment rather than at it
  • Whether the doors are paneled to match the cabinetry, which changes how they come off and go back
  • The diagnosis first, then the scope and the price in writing, and your approval before anything is opened

What it costs, and what moves the figure

Prices in Pompano Beach are the same as everywhere else we cover: a diagnostic from $89 that is credited toward the repair, and starting figures per job rather than one number for "a repair". What moves it is the model, how the appliance is built into the cabinetry, which part it needs and how quickly that part can be sourced — none of which can be judged over the phone. The repairs we carry out lists what each job involves and the figure it starts at, and the unit pages covers what tends to go wrong on each type.

The exact cost is confirmed after the on-site diagnostic and agreed with you before any work begins. We are an independent repair company — not affiliated with, authorized by, or endorsed by any manufacturer — and our warranty covers the labor we performed.

Before you book

Questions about a visit in Pompano Beach

Do you cover Pompano Beach?

Yes. Pompano Beach is in Broward County and inside the area we work every week. Give us the address when you book, and say how the Maytag is installed — what has to come apart to reach it matters as much as where it is.

How soon can you get to Pompano Beach?

We will tell you the earliest slot we can genuinely keep rather than the earliest one that sounds good. Tell us the model number and what the unit is doing when you book: whether we can finish the same day depends on the part far more than on the drive.

Does it cost more because the job is in Pompano Beach?

No. The diagnostic and the work are priced the same across Miami-Dade, Broward and Palm Beach. What moves the figure is the model, how the unit is built in and which part it needs — never the address. Where access takes longer, we say so before anything is agreed rather than after.

My building has rules about service calls. What do you need?

The building name when you book, and anything it requires — a service elevator window, a loading bay slot, approved hours or a certificate of insurance. We arrange those in advance; found out on the day, they cost the appointment.

Booking a visit in Pompano Beach

Tell us the model number and what the unit is doing. We will bring the parts that problem usually needs, and you will have a firm price before we start.

Schedule a visit Call (305) 853-8839

This article is based on:

  • Official manufacturer documentation
  • Internal repair procedures
  • Technician repair history
  • Company quality standards
Call (305) 853-8839